banner
Home / Blog / Explained: How To Reset RGB LED Controller?
Blog

Explained: How To Reset RGB LED Controller?

May 21, 2024May 21, 2024

All possible ways to reset the controller.

If you like to illuminate your PC or your room in general, you definitely use LED light strips. These are useful, power-efficient lights that can be installed anywhere. However, if you have been using them for a while, you might have encountered an issue with the remote control that comes with them. If so, you need to learn about how to reset RGB LED controller.

Key Takeaways

But what exactly can cause the RGB controllers to cease functioning correctly? There are 2 apparent factors:

Your RGB LED controller might stop working partially or entirely, and this is due to interference between the controller and the strips. This may be caused due to weak batteries, weak signals, or radio waves causing interruptions between the remote and the strips.

In addition to a faulty controller, problems can arise with the LED strips themselves. The LED strips may trip if they don’t receive the proper voltage, which can occur if they are not connected properly. Furthermore, the LED strips can malfunction due to too much heat. LED strips work optimally at room temperature, and it’s best to operate them at under 30°C at all times. Finally, you should ensure the LED light strips are not exposed to direct sunlight, as the heat can cause the diodes to change colors.

Following are the ways through which you can reset the controller.

One of the most common methods to reset the remote is by using the reset button on it. If your remote has this function, then you’re set. Here’s how to carry it out:

This method is carried out in a similar way to the above process. Please note that this method will completely reset your remote’s settings, and you will need to reprogram the remote with the LED strips. For this, refer to the manual provided with the package.

The next common method is to replace the batteries on the remote. You should find the battery compartment at the bottom of the remote. Now, here’s how to remove it.

Note: If this doesn’t work, repeat the same method but with new batteries.

You may also be interested to read: How Long Do Power Supplies Last?

If the methods mentioned above don’t work for you, you can use alternate techniques involving the remote’s programming.

A similar method with different programming may work for you if the above method does not. Here’s how this one goes:

Also Read: How to Benchmark Gaming PC?

There are some other methods that might get your remote working normally again if it is acting glitchy or erratic. Mainly if one key enables the function of another (for example: pressing the blue button turns the lights red instead).

This method might be helpful if your RGB LED strips are not turning on through the remote.

Some RGB LED strips are Bluetooth or WiFi controlled in addition to the remote control provided with them. If the remote isn’t behaving properly, you can connect the LED strips to the application on your phone and control them from there.

This depends on the particular brand and model of the strips you’re using. If your LED strips have such a function, you can check the manual provided or the website for the software you have to download.

This guide applies to many cases where your controller is not working correctly. This includes the controller not responding appropriately, randomly flickering lights, or when pressing one button enables the function of another. You’ll also need to reset the controller if you have purchased new LED strips.

These methods will work for most RGB devices as most of the remotes are programmed the same way. So, in any case, this guide will help you restore the factory settings of your RGB LED controller and have it working correctly again.

Also Read: How Much Does a Gaming PC Weigh?

Having a faulty RGB LED controller can be very frustrating. However, in most cases, there is usually a minor issue, such as weak batteries or a weak connection between the remote and the LEDs. In these cases, you can try many easy fixes for which you need to spend no money.

Hence, there are many methods you can try to fix your remote before considering the option of replacing the remote. In any case, we hope that our guide on how to reset RGB LED controller has helped you.

Your RGB LED remote may not be functioning correctly due to weak batteries or weak signals. It’s also possible that the remote is working correctly and the LED strips themselves are faulty.

The easiest way to reset your remote is by using the reset button on the remote. Insert a pin into the small hole until you hear a popping sound.

An easy fix for this is by turning off the LED strips, pressing the button on the bottom-right corner, and then turning them on again. Repeat until the issue is fixed.

Other useful articles:

Thank you! Please share your positive feedback. 🔋

How could we improve this post? Please Help us. 😔

Save my name, email, and website in this browser for the next time I comment.

illuminate your PCLED light stripspower-efficient lightsKey Takeawaysmany waysvary with the particular brand and modelweak batteriesinterferenceimproper pairingissuesremoteLED stripsinterference between the controller and the stripsweak batteriesweak signalsradio waves causing interruptionsproper voltagenot connected properlytoo much heatroom temperatureunder 30°Cdirect sunlight, diodes to change colorslocate the buttonon the backthe sides small hole“reset” label something smallpopping sound3 to 5 seconds,will completely reset your remote’s settings, and you will need to reprogram the remotemanualLocate the “reset” buttonflash10 seconds5 minutesPress on the tiny clippull the the other part outremove the batteryhold the power button10 to 15 seconds the batterypositive terminalfaces the topnew batteriesfew secondsLED strips offremove the power sourceHold the power buttona few secondsContinue pressing5 secondsred, green, and blueyellowthen switch offLED strips onfew secondsLED strips off the power adapterpower button for 5 secondsturn offpower button 3 secondscontinue holding5 secondsRepeat steps 3 and 44 timescontrasting colorsyellowLED strips offSMOOTHFADE7 back onRepeatTurn offturn on the power adapterpower switchsimultaneouslyBluetooth or WiFi controlledparticular brand and modelcheck the manualnot responding appropriatelyrandomly flickering lightsone button enables the function of anothernew LED stripsOther useful articles